So, I lost access to my old site, https://hitlh.blogspot.com/, so I've recreated it here.

Standing on the Corner watching all the Grells go by...
(May 2019)

So I made some Grell (or is it Grells?) out of Greenstuff because they're Great. And I didn't have any and I like the idea of them.

The Grell are done as far as I'm concerned. Just need to get around to painting and basing them. The bases are 25mm square so they're a reasonable size. I guess I'll just paint suckers on the tentacles or whatever. I'm not keen on the spiky bits on the ends of the tentacles in the latest D&D monster manual. Doesn't look right to me - and hard to reproduce at this scale with out being flimsy or bulky :-)

 

How I made the Grell

(May 2019)

The process took a couple of weeks to make the Grell with most of the time waiting for bits to dry overnight.

Tools :

• Magnifier Lamp  - so I can get a good look at what I'm doing on the figure 
• Sculpting Tools - to push greenstuff around. 
• Gardening Wire - got this from the local hardware store. It's 1mm thick or possibly less.
• Greenstuff - blue/yellow epoxy, kneadatite
• Glue Gun - mainly to glue the wire to the stand so it didn't flop around
• plastic 25x25mm square base - you can use whatever base you want.

Process :

1. The base - I drilled a hole in a 25x25mm base with my pin vice and stuck a roughy 1 inch long piece of gardening wire into the hole just deep enough so that the base sat flush on the table. I glued it in place under the base with some hot glue. I used hot glue as it sets pretty quick.
2. The body - I put a blob of greenstuff on the top of the wire slightly smaller than I want the brain shape to be and shaped it into a roughly brain shape.
3. Tentacles -  I rolled some greenstuff into a long thin sausage with my finger (a bit less than 1mm?) and cut off about a 15-20mm length. I squashed the end of the sausage on low on one side of the brain shape and then grabbed the other end of the sausage gingerly with my fingers and twisted and looped it until it looked all tetaclely. 
4. I propped the figure against a cup at an angle so that when the tentacle drooped back under its own weight it dried at a funny angle helping it to look like it was lifting its tentacles menacingly. I guess you could also try using bluetack to prop it at whatever angle you like. I left the tentacle to dry.
5. I repeated steps 3 and 4 four more times down one side of the brain, sometimes propping it sideways or backwards against something to vary how the tentacles hung.
6. I repeated 3-5 on the other side of the figure until I had a total of ten tentacles, 5 each side.
7. The body cont. - I rolled some greenstuff into a *very* fine sausage and then cut of roughly 1 inch lengths and using a sculpting tool, attached the sausage to the brain shape, making sure to make a squiggly pattern. I made sure I didn't go over the centre line of the brain shape so that I left a slight gap between left and right hemispheres. I left each section to dry before I continued so that I didn't ruin the pattern by squashing it with my fingers.
8. I repeated step 7 until the brain was covered in squiggly bits and a slight gap between, running from the back to the front and down the middle.
9. The beak. - I squashed some greenstuff to the front of the brain and low down, and shaped that with a sculpting tool into the shape of the lower beak. I made this relatively small as I wanted the upper beak to overhang. I left this to dry.
10. I squashed a larger bit of greenstuff above the lower beak and shaped that with my sculpting tool until it looked beaky enough. I left that to dry.

 

Vargouilles
(October 2018)

So I'm a DM for a couple of  D&D games at the moment (v5e). One group of characters found themselves recently in the infamous bowels of Undermountain. Their first encounter? Vargouilles. I didn't have any miniatures at the time so the ever-present goblins were pressed into service. Having never used vargouilles as an encounter before I found them to be unusual and fun so I decided to make some for future encounters.

Now I have a number of ghoulish/zombie/skeletal heads in my bits box, but no small bat wings. To make these I realised that the little squarish clips used to tie loaves of bread were made of plastic, and so could be used to make the wings. I have a feeling that someone has suggested using these before for model making but I can't for the life of me remember who it would have been but I would love to give them credit for this revelation as they are a great, free alternative to buying plastic card - for making small things anyway.

So after making the wings I selected the heads and cut little slots into the sides of them into which were glued the wings. Here's some GW zombie heads from years ago that I used.

Next I attached them to roughly 5cm lengths of garden fencing wire which was glued into the conveniently placed neck holes. I did use a pin vice to drill a bit deeper for some of the heads.

Next was to curl up the bottom ends of the wire so that they could be easily glued to some 20x20 stands using a glue gun.

I then used a little bit of greenstuff to add the odd tentacle and/or rotting tongue, etc and then finally  painted them and finished the bases.

The painting scheme is inspired by this image. I'm pretty happy with them, especially as they cost so little to make.

As a side note I was pronouncing them as var-goo-eels. My father questioned this as the word looked french and so expected the 'll' sound to not be pronounced ie Var-goo-ee. We looked it up in wiki and found it was pronounced slightly different again. Having thought about it for a little while I reckon my Dad was probably right...this time...;-)

 

Penanggalen
(October 2018)

I had Vargouilles and Penanggalen mixed up in my head (see what I did there?) but I then watched a movie called 'Mystics in Bali' from 1981 that featured this strange vampire like creature. As I was making Vargouilles anyway I thought I'd make this one at the same time.

Like the Vargouilles, this is basically a head from the bits box stuck on some garden fencing wire and then the wire was wrapped in bits of green stuff to act as various internal organs.

Another cheap miniature ready to use in a future D&D (5e) game.

 

Flameskulls (July 2018)

 

Flameskulls
(July 2018)

These Dungeons and Dragons monsters were pretty easy to make. I twisted two bits of garden wire around a pencil to make spiral shapes. One end of each I glued into the 20x20mm base after drilling some holes with a pin vice. I then drilled some holes into the backs of two GW plastic skulls I had lying around and glued them to the other ends of the spiral wire shapes. Then I put some greenstuff on the wire to make the trails of flames.

Stirges

(March 2018)

So I saw a youtube on how to make stirges using plastic leaves and a glue gun. It looked really easy and surprisingly effective. I decided to make some stirges as well but with wire and greenstuff.

The wings were two little blobs of greenstuff with some wire snipped and pushed into them. I shaped the wings roughly into little diamonds and let them set. After they had set I held them between the wings with some needle nose pliers and bent the wings up a bit to look a bit more natural.

At the same time I snipped off roughly 50mm of wire to serve as a stand. I bent about 8mm of each end at 90 degrees to the stand. One end was glued to a 20x20mm cardboard square and with the other I wrapped some greenstuff sausage shapes, leaving a couple of mm poking outside the sausage to serve as the proboscis. I did a bit of prodding with my knife to form a round shape at one end for the head, a gap in the middle for where the wings will be glued, and then dragged the knife down the body from the head to the rear, so that it looked like it had some hair, and let the body hang out past the stand so it looked like the wire stand attached more toward the middle of the body.

I let the body set and then glued the wings to the body. I got two tiny blobs of greenstuff and squashed them onto the head to form eyes and then painted the little beasts.

For a little bit more time and effort than Scotty in the youtube, I had me some stirges ready to swoop on the next lot of low level characters in my game. Looking at them now, I really should have just stuck some pins through some dead flies and be done with it ;-)